Flame detector

دتکتور های خطی لیزری Open Path Gas Detector شامل دو سری ds900 و ds700 می باشند که در این پست به توضیح آن می پردازیم.

دتکتور های خطی لیزری Open Path Gas Detector سری DS 900 :

سری SafEye Quasar 900 از جدیدترین فن آوری open path IR برخوردار می باشد که طیف گسترده ای از گازهای هیدروکربنی  از جمله آلکان (متان به) هگزان) و اتیلن را شناسایی می کند.
در این مدل طول مسیر می تواند تا 660 فوت (200 متر) باشد و برای محافظت از نصب پر ریسک شما می توانید از مدل های Quasar 900 استفاده کنید.
قابلیت اطمینان و کارایی کلیدی است و با تأیید SIL2 و آزمایش عملکردموفق و دارا بودن استانداردهای FM و EN از این محصول اطمینان داشته باشید.

Why Open Path Gas Detectors?

Spectrex invented the xenon flash lamp design that revolutionized the open-path gas detection market, which, until then, was plagued by false alarms due to the drawbacks of the previous designs.
Now, Open path detectors complement the use of individual point detectors, take executive action and offer many significant benefits including:
• Wider area coverage
• Most likely method to pick up any leak
• Very high speed of response
• No unrevealed failure modes
• Beam block warning
• Detector location is less critical
• Size of gas hazard indicated

Applications include:

• Offshore platforms & FPSOs
• Petrochemical plants
• Chemical processing plants
• Gas filling and distribution terminals
• Gas transport and pipelines
• Large storage areas & buildings
• Perimeter monitoring

ds 900 دتکتور های خطی لیزری Open Path Gas Detector
Installation Options

QUASAR OFFERS OPTIONS FOR YOUR INSTALLATION:
0-20mA analog output with HART capability
• RS485 Modbus, where up to 256 detectors can be linked

 

Worldwide Approvals

• Hazardous area (Zone 1) FM/FMC, ATEX, IECEx, GOST R Inmetro
• Performance (3rd party):
FM 6325 approved by FM
EN60079-29-4 tested by FM
• Reliability:
SIL2 (TUV)

HART

HART capabilities within the Quasar 900 can provide digital communications between the field and the safe area.
This can provide real time information on the status of an individual detector as well as configuration and historical data of each device, without the need for extra cable cores.
A key feature of HART is that digital signals are transmitted on the same two wires as the 0-20mA current signal.
Useful and useable information available via HART includes:
• Display set-up
• Reconfigure set-up – such as gas
calibration, heater control, address
• Display detector status and definition
• Perform detector diagnostics
• Troubleshooting
• View Event Log

ds-g-900-2 دتکتور های خطی لیزری Open Path Gas Detector

دتکتور های خطی لیزری Open Path Gas Detector سری ds 900 :

این تصویر نشان می دهد که چگونه ماتریس آشکارسازهای نوع نقطه ای می توانند نشتی را از دست بدهند یا در نهایت فقط سطح گاز رقیق شده را مشاهده کنند در حالی که SafEye 700S Open-Path ، در این حالت 20٪ LEL x 7 m = 1.4 LEL.m را اندازه می گیرد.

ds-g-700 دتکتور های خطی لیزری Open Path Gas Detector

Open-path Gas Detection Concepts

Not all gas clouds are hazardous – only if a flammable gas cloud or plume is wide enough to allow flame acceleration to speeds greater than 100 m/sec does it become a significant threat.

•Just as an athlete performing the long jump needs a run-up distance, so too a flame front needs distance to reach the velocities which cause the damaging effects of over pressure, pressure pulse and windage.

•The generally accepted quantity of gas that creates the potential to cause consequential damage if ignited is a cloud of the size 5 m diameter a stoichiometric concentration (about200% LEL).

• To provide a safety margin, this concentration is halved to 100% LEL. Thus an open path beam traversing this cloud would indicate 5 LEL.m.

•Location of the SafEye 700S Open-Path Gas Detector is less important than with point type detectors as it provides a warning alarm from a diluted gas cloud and does not need to be close to the leakage source.

• Point type detectors measure gas at their location in terms of % LEL, whereas open-path gas detectors measure the amount of gas anywhere along the length of the path, in terms of the integral of concentration and length (LEL x meters).

Open-Path Applications:

•Offshore Oil & Gas drilling and production
•Petrochemical and Chemical storage and ذproduction areas
•Storage & loading of hazardous materials and waste areas
•Engine & Turbine air intake and modules
•LNG-LPG storage, pumping and filling
•Fence-line emission monitoring
•Storage Tank Farm protection
•Paint industries, including paint-booths
•Bus terminals (natural gas powered)
•Waste disposal and processing

برای مشاهده ی تستر  دتکتور های فلیم  spectrex به اینجا مراجعه کنید.

همچنین برای کسب اطلاعات بیشتر می توانید به وب سایت spectrex به آدرس www.spectrex.net مراجعه کنید.

تستر دتکتور spectrex

برای ایمن سازی کامل در برابر آتش ، خودآزمایی (Self Test) آشکارساز شعله کافی نیست. طبق گفته اکثر مراجع محلی و طبق درخواست گواهی نامه SIL2 ، شما باید حداقل یک بار در سال یکپارچگی کل سیستم تشخیص شعله خود را آزمایش و از صحت کارکرد آن اطمینان حاصل کنید. این به معنای انجام یک تست Loop کامل سیستم از دتکتور تا سیم کشی به کنترل پنل و تا اطلاع رسانی هشدار ها و زنگ هاست. تنها راه برای انجام این کار ، بدون روشن کردن آتش واقعی ، با یک شبیه ساز شعله خارجی است.تستر دتکتور spectrex در دو نوع زیر معرفی میگردد.

To be fully secure against fire, flame detector self-testing is not enough. According to most local jurisdictional authorities and as required for SIL2 compliance, you need to test and ensure the integrity of your entire flame detection system at least once per year. That means performing a full system loop test from the detector, through the wiring to the controller, and up to the actual alarm notification. The only way to do so, without lighting a real fire, is with an external flame simulator.

تستر نوع fs1200

Complete End-to-End Testing Using our Flame Simulator

The FS-1200 FLAME SIMULATOR is the essential complimentary tool to the self-testing capabilities of your Sharpeye™ UV and UV/IR Flame Detectors. It brings fire prevention safety to a higher level by giving you the ability to fully test the operational readiness of your entire fire detection system: • Test the integrity of all the system components: all alarm outputs, all cabling and connections and the fire alarm panel functionality. • Test clear line of sight: By using the Spectrex Flame Simulator, you will ensure that no object is obstructing the field of view, and that the detector’s window lens is not obscured. Therefore, by simulating a fire that actually triggers the detector outputs, the model FS-1200 verifies the correct operation of the UV and UV/IR flame detector, performs an essential end-to-end loop test and verifies window cleanliness.

Key Benefits تستر دتکتور spectrex

• Long-range flame detector activation – at a range up to 20ft (6m) – a 33% increase compared to previous simulator models.
• Reduced maintenance costs with easy access for testing detectors, in hard to reach places, from floor/deck level without the need for scaffolding or ladders
• Highly portable – for hand held operation by a single operator
• ATEX/IECEx approved for use in Zones 1 and 2 hazardous areas
• Single charge is sufficient to test up to 100 detectors

FS-1200 Flame Simulator at Work

The Spectrex flame simulator emits IR radiation in a unique pattern corresponding to, and recognizable as fire by your SharpEye Flame Detector. This allows the detector to be tested under “real” fire conditions without the associated risks of an open flame.

DS-F-FS-120

 

 

ABOUT SharpEye

The SharpEye range of Optical Flame Detectors includes a wide variety of technologies such as IR3, Multi-IR, UV/IR, all providing reliability, performance and durability. These flame detectors are equipped with a range of output options, ensuring maximum compatibility, and a wide range of approvals to ensure suitability for a variety of industries, from high risk to commercial.

sharpeye-DS-F-FS-1200_

Technical Specifications تستر دتکتور spectrex

The Flame Simulator Kit, Part No. 380114-2 includes the FS-1200 Flame Simulator, battery, charger, tool kit and user guide TM380102 in carrying case

Table-DS-F-FS-1200

تستر نوع fs1100

Complete End-to-End Testing Using our Flame Simulator

The FS-1100 FLAME SIMULATOR is the essential complimentary tool to the self-testing capabilities of your Sharpeye™ IR3 Flame Detectors. It brings fire prevention safety to a higher level by giving you the ability to fully test the operational readiness of your entire fire detection system:
• Test the integrity of all the system components:
all alarm outputs, all cabling and connections and the fire alarm panel functionality.
• Test clear line of sight: By using the Spectrex Flame Simulator, you will ensure that no object is obstructing the field of view, and that the detector’s window lens is not obscured.
Therefore, by simulating a fire that actually triggers the detector outputs, the model FS-1100 verifies the correct operation of the IR3 detector, performs an essential end-to-end loop test and verifies window cleanliness.

Key Benefits تستر دتکتور spectrex

• Long-range flame detector activation – at a range up to 40ft (12m) – a 33% increase compared to previous simulator models.
• Reduced maintenance costs with easy access for testing detectors, in hard to reach places, from floor/deck level without the need for scaffolding or ladders
• Highly portable – for hand held operation by a single operator
• Easy aiming using laser diode
• ATEX/IECEx approved for use in Zones 1 & 2, Zones 21 & 22 hazardous areas
• Single charge is sufficient to test up to 1,000 detectors

FS-1100 Flame Simulator at Work

The Spectrex flame simulator emits IR radiation in a unique pattern corresponding to, and recognizable as fire by your SharpEye Flame Detector.
This allows the detector to be tested under “real” fire conditions without the associated risks of an open flame.

ds-f-fs-1100

ABOUT SharpEye تستر دتکتور spectrex

The SharpEye range of Optical Flame Detectors includes a wide variety of technologies such as IR3, Multi-IR, UV/IR, all providing reliability, performance and durability.
These flame detectors are equipped with a range of output options, ensuring maximum compatibility, and a wide range of approvals to ensure suitability for a variety of industries, from high risk to commercial.

Technical Specifications

table-ds-f-fs-1100

برای کسب اطلاعات بیشتر در مورد تستر دتکتور spectrex به سایت www.spectrex.net مراجعه کنید.

دتکتور شعله Spectrex سری 40/40 (یا LB با Built-in-test option) ترکیبی از سنسورهای UV و IR را فراهم می کند، که  سنسور IR آن دارای  طول موج 2.5-3.0 میکرومتر می باشد و می تواند آتش سوزی هایی که پایه ی هیدروکربن، هیدروکسیل و هیدروژن دارند  و همچنین آتش سوزی های فلزی و غیر آلی را تشخیص دهد.

دتکتور شعله Spectrex سری 40/40

The UV/IR flame detector senses radiant energy in the short wave section of both the ultraviolet and infrared portions of the electromagnetic spectrum. The signals from both sensors are analyzed for frequency, intensity and duration. Simultaneous detection of radiant energy in both the UV and IR sensors triggers an alarm signal. The UV sensor incorporates a special logic circuit that helps prevent false alarms caused by solar radiation. Due to increased reliability, the 40/40 Series warranty period has been extended to 5 years and is SIL2 (TUV) approved to IEC 61508.

FEATURES & BENEFITS

• UV/IR Dual-Sensor
• Solar blind
• Automatic Built-In-Test (BIT) and Manual – to assure continued reliable operation (in 40/40LB only) • Heated window – for operation in harsh weather conditions (snow, ice, condensation)
• Multiple output options for maximum flexibility and compatibility
– Relays (3) for Alarm, Fault and Auxiliary
– 0-20mA (stepped)
– HART Protocol for maintenance and asset management
– RS-485, Modbus Compatible

• High Reliability – MTBF – minimum 150,000 hours
• Approved to Safety Integrity Level 2 (SIL2 – TUV)
model 40/40LB only
• 5-Year Warranty
• User Programmable via HART or RS-485
• Hazardous area zones:
– Zones 1 & 2 with IIC gas group vapors present
– Zones 21 & 22 with IIIC dust type present

• Ex approved to:
– ATEX & IECEx
– FM/FMC/CSA

• 3rd party performance approved
– EN54-10 (VdS)
– FM3260
• Marine Approval
– MED ‘Wheelmark’ approval (DNV)

APPLICATIONS (model dependent)

Offshore Oil & Gas
installations
Onshore Oil & Gas installations and pipelines
Chemical plants
Petrochemicals plants
Storage Tank farms
Aircraft hangars
Power Generation facilities
Pharmaceutical Industry
Printing Industry
Warehouses
Automotive Industry
Explosives & Munitions
Waste Disposal facilities
Aerospace Industry
Paint, Polymer and Glue

دتکتور شعله Spectrex سری 40/40 table