بیم دتکتور مدل fireray one بدون داشتن ابزار و دانش تخصصی برای نصب و راه اندازی، یک دتکتور پرتویی مستقل است که سهولت نصب را در اولویت قرار داده است. با کمک دتکتور های FireRay به آسانی دودیابی پرتویی را در کاربرد ها و مکان های متفاوت استفاده نمایید.:
- Auto-Aligns – با استفاده از رابط کاربری یکپارچه – فقط لیزر را روی Reflector هدایت کنید ، سپس در لرزش سوئیچ ، خود را تراز کنید. 8 برابر سریعتر از ردیاب های قبلی
- One person installation – همه کارها توسط یک شخص قابل انجام است
- One standalone product – هیچ ابزار تخصصی لازم نیست. حداقل دانش و آموزش قبلی مورد نیاز است.
Fireray One Key Benefits:
- Integrated visible laser and auto-alignment for ultimate ease of alignment
- Integrated user interface
- Prevent nuisance alarms with Light Cancellation Technology™ which compensates for sunlight and artificial light sources
- Building Movement Tracking™ continuously maintains alignment when buildings settle or flex due to temperature variations
- Contamination Compensation to correct for gradual build-up of dust on optics
- Clean detectors quickly and easily without affecting alignment
- Low power consumption; can be powered from the loop
- Prevent interference between beams with Dynamic Beam Phasing; install beams facing each other or in irregular configurations
- Detection range of up to 120m
Ideal Applications
- Education and Heritage Establishments
- Industrial Units and Warehousing
- Aviation Hangars
- Glass Atria in Hotels and Retail Complexes
- Chemical Processing and Storage Facilities
Fireray one with 1 prism 50m PN EN 6010-100 / UL 6010-300
Long Range Kit 3 prisms 120m PN 1010-000
دانلود دیتاشیت بیم دتکتور مدل fireray one
برای مشاهده سایر بییم دتکتورها اینجا کلیک کنید.
کنترل پنل اطفاء C-Tec
این پنل دارای تاییدیه های LPCB ، EN 12094-1 (استاندارد اروپایی برای سیستم های آتش نشانی ثابت – اجزای سیستم های خاموش کننده گاز) و EN54-2 / 4 میباشد. پنل خاموش کننده اتوماتیک EP203 سه منطقه ، کیفیت ، دوام و قابلیت اطمینان را نشان می دهد.
کنترل پنل اطفاء C-Tec به طور خاص برای استفاده در مناطقی که دارای وسایل گران قیمت ، خطرناک یا غیر قابل تعویض هستند مناسب میباشد.
دارای صفحه نمایش بصری 128*64*64 پیکسلی است که بازخورد واضح و مختصر به کاربر ، نصاب و مهندس راه اندازی می دهد.
تمام وسایل الکترونیکی کنترل پنل اطفاء C-Tec – جدا از حالت قدرتمند سوئیچ 3A EN54-4 PSU – برای سهولت در نصب روی صفحه پل فلزی جدا شده سوار شده اند. طیف گسترده ای از لوازم جانبی از جمله واحدهای وضعیت از راه دور ، دکمه های نگه داشتن، پایان دهنده های خط و تابلوهای رله نیز در دسترس هستند.
اطلاعات بیشتر در مورد کنترل پنل اطفاء C-Tec
- Certified to EN54-2/4 and EN12094-1 by the Loss Prevention Certification Board (LPCB)
- Functions as a standard 3 zone fire panel with additional circuitry for controlling the release of fire-suppressing gas.
- 128 x 64 pixel display.
- Any combination of activated zones can be programmed to automatically start the panel’s extinguishant release sequence.
- Manual release button and two keyswitches.
- 3 conventional sounder circuits (two x 1st stage, one x 2nd stage).
- Powerful 3A EN54-4 switch mode PSU.
- Wide range of monitored inputs and auxiliary outputs.
- Abort and hold inputs.
- Time-stamped event log.
- RS485 connections for up to 8 flush or surface remote status units with their own LCDs, manual release and mode switches. Single gang economy status units also available.
- Wide range of engineering functions.
- Optional relay expansion boards and single gang abort & hold buttons
- Ideal for use in computer rooms, telecommunication centres, archive storage areas, museums, etc.
- System line terminator included.
Technical Specifications
| Approvals/certifications | Certified to EN12094-1 and EN54-2/4 by the LPCB (176c) / (0832-CPD-0794). |
| Mains supply | 230V 50/60Hz. |
| Mains rated current | 810mA max. |
| Internal power supply | 19V-28.5V (27V nominal). Ripple 7V maximum (battery fault). |
| Total output current limited to | 1.5A @ 230Vac continuous, 3A peak (ImaxA eq 800mA). |
| Quiescent current | 40mA (on mains fail). Zone quiescent 2mA max. |
| Max battery size and type | 2 x 12V 7Ah VRLA connected in series. |
| No. of detector zone circuits | 3 @ 19-28Vdc (Max. length per circuit is 250m). |
| Max. devices per detector zone | 20 detectors (or 32 detectors/manual call points combined). |
| No. of conventional sounder circuits | 3 (two x 1st stage; one x 2nd stage). Max. length per circuit is 50m). |
| EOL resistor value | 6800Ω 5% Tol. 0/25W (blue, grey, red, gold). |
| Max. sounder output current | 3 x 200mA. |
| Auxiliary relays | Six: (1) Fire; (2) Local Fire; (3) Extract Fan; (4) 1st Stage; (5) 2nd Stage; (6) Fault. Volt free single pole changeover. Max. switch current 1A; Max. switch voltage 30Vdc. Five additional relays available via EP212 relay card. |
| Other outputs | Extinguishant release (21-28Vdc, rated at 1A for 5 mins). Programmable to delay by 0-60 seconds; to be active for 1-300 seconds and to flood for 60-1800 seconds. |
| Auxiliary inputs | Six: (1) Manual Release; (2) Flow Switch; (3) Low Pressure; (4) Mode; (5) Hold; (6) Abort. 8K-2KΩ normal; 1.8K-200Ω active; 150-0Ω short circuit. EOL value: 6K8 +/-5%, 0.25W. |
| Indicators | Multiple indicators are provided – refer to the EP203 instructions for details. |
| Controls | Extinguishant release (housed in yellow casing); Accessed keyswitch; Operation keyswitch (Manual only or Manual & Auto); Buttons for Menu; Silence internal sounder; reset panel; silence/resound sounders and scrolling. |
| Expansion connections | Yes – for up to 8 x Remote status units (2 wire RS485 + 2 wire power) and/or up to 8 x Ecomomy status units (2 wire power + 2 wire mode select). |
| Product dimensions (mm) | 439 W x 276 H x 70 D mm (back box); 467 W x 293 H x 29 D mm (lid). |
| Construction & finish | Metal back box; metal chassis’ plastic lid. |
| IP Rating | IP30. |
| Weight | 4.2kg (without batteries). |
| Operating conditions/temperature | -5ºC to +40ºC. Max relative humidity: 95%. |
کنترل پنل اطفاء C-Tec
Dimensions & Mounting Information
| Product dimensions (overall): | 467 W x 293 H x 85 D mm. |
| Hole required for flush mounting: | 440 W x 277 H x 40 D mm. No bezel available. |
Automatic for the People
With the growing emphasis on safeguarding property as well as people, the market for automatic fire suppression systems is booming. Comprising a third-party certified three zone automatic extinguisher panel and host of expansion ancillaries, C-TEC’s EP Range has been specifically designed to meet this demand. Ideal for areas housing expensive, dangerous or irreplaceable items of equipment such as computer suites, libraries & art galleries, telecommunication centres, archive storage areas, chemical plants and generator rooms, it includes a wealth of features, many of which are not available on more expensive extinguishing equipment.
Auto Express!
C-TEC’s EP203 three-zone automatic extinguisher panel is LPCB certified to EN12094-1 and EN54-2/4. Featuring an intuitive 128 x 64 pixel graphic display that gives clear and concise feedback to user and installers, it includes six monitored inputs (including hold and abort), a time-stamped event log, adjustable flood times and changeover relays for fire, local fire, 1st stage active, 2nd stage active, extractor fan and fault. Elegantly-styled in a durable enclosure, the EP203 epitomises quality, durability and reliability.
Rock the Status Quo!
Need to cover a room with multiple entrances? Up to eight flush or surface mountable remote status units, each with their own displays, manual release buttons and mode switches, can be connected to the EP203 control panel via a monitored RS485 bus. Cost-effective single gang economy status units are also available. With so much choice, C-TEC’s EP Range is anything but your standard run-of-the-mill automatic extinguisher system.
Stop! Hold! Abort!
The nature and cost of fire suppressing agents means many installers shy away from extingishant systems with one of their biggest concerns the accidental release of the suppressant in a false alarm situation. Have no fear, C-TEC’s IP66 rated Hold and Abort Buttons can be used to delay (hold off) or cancel (abort) the extinguishant release sequence at any time depending on how they are configured. Job done!
Clever combinations!
Whatever type or size of extinguishant system you’re installing, our all-encompassing range of conventional devices can be combined to suit. We stock a huge range of versatile and cost-effective manual call points and sounders & VADs.
Get ActiV
C-TEC’s ActiV fire detectors include a host of features installers love – plenty of working space, two ultra-bright LED indicator strips offering all-round visibility, an ingenious detector/base locking mechanism and compatibility with virtually all known conventional fire alarm panels. Certified to the relevant parts of EN54-5/7, optical, fixed heat, rate-of-rise and multi-sensor variants are available, all manufactured in the UK. It’s no wonder so many installers are switching to ActiV.
کنترل پنل اطفاء C-Tec
برای کسب اطلاعات در مورد کنترل پنل های NSC به اینجا مراجعه کنید.
دتکتور های خطی لیزری Open Path Gas Detector شامل دو سری ds900 و ds700 می باشند که در این پست به توضیح آن می پردازیم.
دتکتور های خطی لیزری Open Path Gas Detector سری DS 900 :
سری SafEye Quasar 900 از جدیدترین فن آوری open path IR برخوردار می باشد که طیف گسترده ای از گازهای هیدروکربنی از جمله آلکان (متان به) هگزان) و اتیلن را شناسایی می کند.
در این مدل طول مسیر می تواند تا 660 فوت (200 متر) باشد و برای محافظت از نصب پر ریسک شما می توانید از مدل های Quasar 900 استفاده کنید.
قابلیت اطمینان و کارایی کلیدی است و با تأیید SIL2 و آزمایش عملکردموفق و دارا بودن استانداردهای FM و EN از این محصول اطمینان داشته باشید.
Why Open Path Gas Detectors?
Spectrex invented the xenon flash lamp design that revolutionized the open-path gas detection market, which, until then, was plagued by false alarms due to the drawbacks of the previous designs.
Now, Open path detectors complement the use of individual point detectors, take executive action and offer many significant benefits including:
• Wider area coverage
• Most likely method to pick up any leak
• Very high speed of response
• No unrevealed failure modes
• Beam block warning
• Detector location is less critical
• Size of gas hazard indicated
Applications include:
• Offshore platforms & FPSOs
• Petrochemical plants
• Chemical processing plants
• Gas filling and distribution terminals
• Gas transport and pipelines
• Large storage areas & buildings
• Perimeter monitoring
Installation Options
QUASAR OFFERS OPTIONS FOR YOUR INSTALLATION:
• 0-20mA analog output with HART capability
• RS485 Modbus, where up to 256 detectors can be linked
Worldwide Approvals
• Hazardous area (Zone 1) FM/FMC, ATEX, IECEx, GOST R Inmetro
• Performance (3rd party):
FM 6325 approved by FM
EN60079-29-4 tested by FM
• Reliability:
SIL2 (TUV)
HART
HART capabilities within the Quasar 900 can provide digital communications between the field and the safe area.
This can provide real time information on the status of an individual detector as well as configuration and historical data of each device, without the need for extra cable cores.
A key feature of HART is that digital signals are transmitted on the same two wires as the 0-20mA current signal.
Useful and useable information available via HART includes:
• Display set-up
• Reconfigure set-up – such as gas
calibration, heater control, address
• Display detector status and definition
• Perform detector diagnostics
• Troubleshooting
• View Event Log
دتکتور های خطی لیزری Open Path Gas Detector سری ds 900 :
این تصویر نشان می دهد که چگونه ماتریس آشکارسازهای نوع نقطه ای می توانند نشتی را از دست بدهند یا در نهایت فقط سطح گاز رقیق شده را مشاهده کنند در حالی که SafEye 700S Open-Path ، در این حالت 20٪ LEL x 7 m = 1.4 LEL.m را اندازه می گیرد.
Open-path Gas Detection Concepts
Not all gas clouds are hazardous – only if a flammable gas cloud or plume is wide enough to allow flame acceleration to speeds greater than 100 m/sec does it become a significant threat.
•Just as an athlete performing the long jump needs a run-up distance, so too a flame front needs distance to reach the velocities which cause the damaging effects of over pressure, pressure pulse and windage.
•The generally accepted quantity of gas that creates the potential to cause consequential damage if ignited is a cloud of the size 5 m diameter a stoichiometric concentration (about200% LEL).
• To provide a safety margin, this concentration is halved to 100% LEL. Thus an open path beam traversing this cloud would indicate 5 LEL.m.
•Location of the SafEye 700S Open-Path Gas Detector is less important than with point type detectors as it provides a warning alarm from a diluted gas cloud and does not need to be close to the leakage source.
• Point type detectors measure gas at their location in terms of % LEL, whereas open-path gas detectors measure the amount of gas anywhere along the length of the path, in terms of the integral of concentration and length (LEL x meters).
Open-Path Applications:
•Offshore Oil & Gas drilling and production
•Petrochemical and Chemical storage and ذproduction areas
•Storage & loading of hazardous materials and waste areas
•Engine & Turbine air intake and modules
•LNG-LPG storage, pumping and filling
•Fence-line emission monitoring
•Storage Tank Farm protection
•Paint industries, including paint-booths
•Bus terminals (natural gas powered)
•Waste disposal and processing
برای مشاهده ی تستر دتکتور های فلیم spectrex به اینجا مراجعه کنید.
همچنین برای کسب اطلاعات بیشتر می توانید به وب سایت spectrex به آدرس www.spectrex.net مراجعه کنید.
دتکتورهای دود OSID
تشخیص تصویربرداری از دود در فضای باز (OSID) توسط Xtralis یک نوآوری جدید در فن آوری تشخیص دود پرتویی می باشد. که در این پست به بررسی دقیق آن می پردازیم:
Unique Detection Technology
The OSID system measures the level of smoke entering beams of light projected over an area of protection. A single OSID Imager can detect up to seven Emitters to provide a wide coverage area. Two innovations in smoke detection technology have been developed for the revolutionary OSID smoke detector.
Dual Wavelength Particle Detection
The beam projected from each Emitter contains a unique sequence of ultraviolet (UV) and infrared (IR) pulses that are synchronised with the Imager and enable the rejection of any unwanted light sources. By using two wavelengths of light to detect particles, the system is able to distinguish between particle sizes. The shorter UV wavelength interacts strongly with both small and large particles while the longer IR wavelength is affected only by larger particles. Dual wavelength path loss measurements therefore enable the detector to provide repeatable smoke obscuration measurements, while rejecting the presence of transient dust particles or solid intruding objects.
Optical Imaging with a CMOS Imaging Chip
An optical imaging array in the OSID Imager provides the detector with a wide viewing angle to locate and track multiple Emitters. Consequently, the system can tolerate a much less precise installation and can compensate for the drift caused by natural shifts in building structures.
Optical filtering, high-speed image acquisition and intelligent software algorithms also enable the OSID system to provide new levels of stability and sensitivity with greater immunity to high level lighting variability.
Operation
Status information (Fire Alarm, Trouble and Power) is communicated through the Imager via Status LEDs, dedicated Trouble and Alarm relays, and the Remote Indicator interface. Specific Trouble (Fault) conditions are identified through coded flashes of the Trouble LED.
An internal heating option is also provided on the Imager to prevent condensation on the optical surface, and a reset input enables an external signal to reset the device.
Simple Installation and Maintenance
The OSID system consists of up to seven Emitters for the 90° Imager unit, located along the perimeter of the protected area, and an Imager mounted opposite. Each component can be mounted directly to the surface or can be secured with the supplied mounting brackets. Battery powered Emitters with three or five years battery life are also available to reduce installation time and cost.
Features
• Maximum detection range of 150 m (492 ft) for the OSI-10
• Dual wavelength LED-based smoke detection
• Optical imaging with CMOS imaging chip
• On-board event log for fault and alarm diagnostics
• High tolerance to false alarm due to building movement
• High tolerance to transient dust, steam and intrusion of solid objects
• Easy alignment with large adjustment and viewing angles
• No need for precise alignment
• Tolerant of alignment drift
• Automatic commisioning in under ten minutes
• Simple DIP switch configuration
• Simple and easy maintenance requirements
• Three selectable alarm thresholds
• Status LEDs for Fire, Trouble and Power
• Conventional alarm interface for straightforward fire system integration
Configuration Options
OSID systems may be configured to suit a range of detection spaces by selecting the number of Emitters and type of Imager. Each type of Imager differs by the lens used in the unit, which determines the field of view and range of the system.
Emitter / Imager Dimensions
برای مشاهده ی سایر محصولات Xtralis به اینجا و برای کسب اطلاعات بیشتر در ارتباط با دتکتورهای دود OSID به اینجا مراجعه کنید.
آپولو با داشتن طیف گسترده ای از اینترفیس ها، شما را قادر می سازد تا بدون نیاز به هیچگونه طراحی خاص یا سفارشی ، تمامی دیوایس های آدرس پذیر را به آنها متصل کنید.
ماژول ورودی/ خروجی Apollo XP95
Product code:55000-847APO
The Input / Output Unit provides a voltage-free, double pole changeover (DPCO) relay output, a single monitored switch input and an unmonitored, non-polarised input.
Product code: 55000-852APO
The Sounder Control Unit is used to control the operation of a zone of conventional sounders and report their status to the control panel.
The sounder control unit with isolator allows the device to be operated continuously or be pulsed with 1 second on and 1 second off.
The Devices can be operated individually or in groups and whichever address mode has been applied, may be synchronised when in pulsed operation.
Product code:55000-845APO
The Zone Monitor powers and controls the operation of a zone of up to 20 Apollo Series 65 or Orbis Fire Detectors from a Discovery or XP95 loop.
The Zone Monitor with Isolator is loop powered and operates at 17–28V DC with protocol pulses of 5–9V.
Product code:55000-849APO
The Output Unit provides a voltage free single pole, changeover relay output. It is a simplified version of the Input/Output Unit without circuitry for monitoring inputs.
برای کسب اطلاعات بیشتر در مورد اینترفیس های آپولو به این لینک مراجعه نمایید: سایت رسمی آپولو
سایر محصولات آپولو در ایمن آریا حریق : صفحه آپولو | Apollo
دامنه دتکتور های سری 65 از آشکارسازهای متعارف، شامل فن آوری سنجش فوق العاده ، همراه با استفاده از مواد پیشرفته و فن آوری الکترونیک نوین، جهت اخذ تأییدیه های بین المللی می باشد.
دتکتور دودی سری 65
Product code: 55000-316APO
The Series 65 Optical Smoke Detector incorporates a pulsing LED located within the housing of the detector. The external detector moulding is identical to that of the ionisation detector, and has an indicator LED which is clear in quiescent state but produces a red light in alarm.
دتکتور های حرارتی سری 65
Product code: 55000-121APO
The Series 65 Heat Detector monitors temperature by using a dual thermistor network which provides a voltage output proportional to the external air temperature. There are 12 heat detectors in the Series 65 range designed to suit a wide variety of operating conditions.
پایه استاندارد سری 65
Product code: 45681-200APO
e Series 65 Standard Base has been designed to enable detectors to be fitted without the need of force – particularly useful when fitting to suspended ceilings. All Series 65 bases have a one-way only fit. Detectors can be locked into place by a grub screw using a 1.5mm
hexagonal screwdriver.
شرکت Apollo با تخصص در طراحی و ساخت راه حل های با کیفیت بالا برای شناسایی آتش برای کاربردهای تجاری و صنعتی است. بیش از 40 سال است که محصولاتی را طراحی و ساخته اند که موجب نجات جان انسان ها و محافظت از اموال در معرض خطر آتش سوزی می شوند.
Discovery طیف وسیعی از دتکتور های آدرس پذیر است که برای استفاده در مکان های تجاری ، صنعتی ، مالی ، دولتی ، IT / ارتباطات از راه دور و مراقبت های بهداشتی مناسب است. محدوده Discovery به گونه ای طراحی شده است که مشخصات دتکتور های موجود در سیستم های پیشرفته را داشته باشد. پروتکل ارتباطی Discovery همان پروتکل اثبات شده XP95 است که این پروتکل هر دو سری را با هم سازگار می سازد.
دتکتور حرارتی Discovery
Part Number: 58000-400APO
Discovery heat detectors have a common profile with ionisation and optical smoke detectors but have a low air flow resistance case made of self-extinguishing white polycarbonate. For the European standard version of the detector, the five modes correspond to five “classes” as defined in EN 54-5. The classes in this standard correspond with different response behaviour, each of which is designed to be suitable for a range of application temperatures. All modes incorporate “fixed temperature” response, which is defined in the standard by the “static response temperature”.
دتکتور دودی Discovery
Part Number : 58000-600APO
The Discovery Optical Smoke Detector operates using the light scatter principle and is ideal for applications where slow-burning or smouldering fires pose a potential risk.
آژیر فلاشر محیط باز Discovery
Part Number: 58000-005APO
The Discovery Open-Area Sounder Visual Indicator makes full use of the Discovery protocol and has been designed for use in indoor and open areas. When the fire system is being commissioned a ‘Magnetic Wand’ can be used to adjust and test each sounder locally.
شستی با ایزولاتور Discovery
Part Number: 58100-908APO
A seven-segment DIL switch enables addressing of each call point at commissioning stage. When operated, the manual call point interrupts the polling cycle for a fast response. Bi-coloured LEDs indicate isolate and normal conditions.
